Measurement-computing E-1608-OEM User Manual

E-1608-OEM Ethernet-based High-speed Multifunction DAQ Document Revision 1 December 2014 © Copyright 2014 User's Guide

E-1608-OEM User's Guide Installing the E-1608-OEM 10 Setting up the E-1608-OEM for communication across networks In order to communicate with th

E-1608-OEM User's Guide Installing the E-1608-OEM 11 Updating firmware Your DAQ device contains firmware that can be updated in the field if req

12 Chapter 3 Functional Details Analog input modes The E-1608-OEM can acquire analog input data in two basic modes – software paced and hardware pace

E-1608-OEM User's Guide Functional Details 13 Ethernet connector The E-1608-OEM has one 10/100 BASE-T, auto-negotiation, high-speed communicatio

E-1608-OEM User's Guide Functional Details 14 Connector W2 Header connector W2 provides connections for the DIO, external clock I/O, trigger, co

E-1608-OEM User's Guide Functional Details 15 Leave unused input channels either floating or tied to an AGND connector. Source impedances should

E-1608-OEM User's Guide Functional Details 16 Ethernet to the same local network. Typical throughput is not guaranteed if a wireless connection

E-1608-OEM User's Guide Functional Details 17 Figure 6. W3 jumper configurations For more information about digital signal connections For gene

E-1608-OEM User's Guide Functional Details 18 Mechanical drawings Figure 7. E-1608-OEM dimensions

Chapter 4 Specifications All specifications are subject to change without notice. Typical for 25 °C unless otherwise specified. Specifications in it

HM E-1608-OEM.docx Your new Measurement Computing product comes with a fantastic extra — Management committed to your satisfaction! Thank you for

20 Accuracy Analog input DC voltage measurement accuracy Table 2. DC Accuracy components and specifications. All values are (±) Range Gain error (% o

21 Analog output Table 5. Analog output specifications Parameter Condition Specification Number of channels 2 Resolution 16 bits Output ranges Cali

22 Analog input/output calibration Table 9. Analog input/output calibration specifications Parameter Specification Recommended warm-up time 15 minute

23 External trigger Table 11. External trigger specifications Parameter Condition Specification Trigger source External digital TRIG Trigger mode Sof

24 Counter Table 13. Counter specifications Parameter Specification Pin name CTR Counter type Event counter Number of channels 1 Input type Schmitt t

25 Network Ethernet connection Table 16. Ethernet connection specifications Parameter Specification Ethernet type 100 Base-TX 10 Base-T Communication

26 LED displays and the factory reset button Table 20. LED and button configurations Parameter Specification Power LED (top) 3.3 V < Vext < 5.9

27 Table 24. W2 pinout Pin Signal name Pin description Pin Signal name Pin description 1 DIO0 DIO channel 0 2 DIO1 DIO channel 1 3 DIO2 DIO channel 2

28

Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: [email protected]

3 Table of Contents Preface About this User's Guide ...

E-1608-OEM User's Guide 4 Analog input DC voltage measurement accuracy ...

5 Preface About this User's Guide What you will learn from this user's guide This user's guide describes the Measurement Computing E-1

6 Chapter 1 Introducing the E-1608-OEM The E-1608-OEM is compatible with both TCP/IP (IPv4 only) and user datagram protocol (UDP) network protocols.

E-1608-OEM User's Guide Introducing the E-1608-OEM 7 Functional block diagram E-1608-OEM functions are illustrated in the block diagram shown he

8 Chapter 2 Installing the E-1608-OEM Unpacking As with any electronic device, you should take care while handling to avoid damage from static elect

E-1608-OEM User's Guide Installing the E-1608-OEM 9 Configuring network settings The following E-1608-OEM network settings are software-selectab