Measurement-computing Digital488 User Manual Page 29
- Page / 83
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 2 Getting Started
2.13
2.5 Installation
To begin operating the
Digital488,
plug the external power supply into the rear
jack on the interface.
CAUTION
Never install the power supply into the interface
while it is connected to AC line power. Failure to
observe this caution may result in damage to the
Digital488.
WARNING
The power supply provided with the interface is
intended for INDOOR USE ONLY. Failure to
observe this warning could result in equipment
failure, personal injury or death.
After installing the power supply connector into the interface, turn on the
Digital488
by depressing the rear panel power switch. All the front panel LEDs should
light for approximately one second while the
Digital488
performs an internal ROM
and RAM self check. At the end of this self check all indicators should turn off except
POWER
.
If you obtain the above response then your
Digital488
is alive and well. If all
LEDs remain on, then a ROM error has occurred. If all LEDs continue to flash (except
the power LED), then a RAM error has occurred. Try cycling the power to the
Digital488
to determine that the error is repeatable.
If the LEDs do not flash and the
POWER
indicator does not remain lit, there
may not be any power supplied to the interface. In this event, check to make sure the
AC power is supplied to the power supply, and that the supply is properly installed into
the unit. If the problem is unresolved, refer to the
Service Information
section of this
manual.
- Digital488 3
- Digital488OEM 3
- Instruction Manual 3
- Table of Contents 5
- Introduction 9
- Section 1 Introduction 10
- 1.3 Specifications 11
- &$87,21 12
- Digital488/OEM Specifications 13
- Digital I/O 13
- IEEE 488 13
- Getting Started 17
- IEEE Address = 18 18
- CR Only LF Only 19
- EOI Enabled EOI Disabled 19
- CR-LF LF-CR 19
- 210 20 30 40 50 20
- 4939199129 20
- 65 µS typ 50 µS typ 22
- DCL, SDC or IFC 22
- DATA VALID 23
- 15 µS min 23
- 50 µS typ† 23
- † 15 µS typ in F5 Format 23
- 75 µS typ 50 µS typ 25
- Command Descriptions 31
- Serial Poll Status Byte 54
- IEEE 488 Primer 61
- Section 4 IEEE 488 Primer 63
- 4.3 SEND IT TO MY ADDRESS 64
- 4.4 BUS MANAGEMENT LINES 64
- 4.4.1 Attention (ATN) 64
- 4.4.2 Interface Clear (IFC) 65
- 4.4.3 Remote Enable (REN) 65
- 4.4.4 End or Identify (EOI) 65
- 4.4.5 Service Request (SRQ) 65
- 4.5 HANDSHAKE LINES 66
- 4.5.1 Data Valid (DAV) 66
- 4.6 DATA LINES 67
- 4.7 MULTILINE COMMANDS 67
- 4.7.1 Go To Local (GTL) 67
- 4.7.6 Local Lockout (LLO) 68
- 4.7.7 Device Clear (DCL) 68
- 4.8 MORE ON SERVICE REQUESTS 70
- 4.8.1 Serial Poll 71
- 4.8.2 Parallel Poll 71
- Service Information 73
Related products and manuals for Hardware Measurement-computing Digital488
(126 pages)Whirlpool AWA 6125 manuales
Manuales del propietario y guías del usuario para Lavadoras Whirlpool AWA 6125.
Ofrecemos 1 manuales en pdf Whirlpool AWA 6125 para descargar gratis por tipos de documentos: Instrucciones de uso
Comments to this Manuals